Biotin (Type 1) Conjugation Kit

//www.bio-rad-antibodies.com/biotin-type-1-conjugation-kit-lnk261b.html?RenderPageSpecific=1
Biotin (Type 1) Conjugation Kit gallery image 1

Purchased this product? Why not be the first to submit a review and upload an image?

Enlarge
  • Biotin (Type 1) Conjugation Kit thumbnail image 1
  • LYNX Rapid Plus Biotin (Type 1) Antibody Conjugation Kit
  • LYNX Rapid Plus Biotin (Type 1) Antibody Conjugation Kit
  • LYNX Rapid Plus Biotin (Type 1) Antibody Conjugation Kit
(Rated 0.0 out of 5 based on 0 customer reviews)
  • Product Type
    Conjugation Kit
1 Formats Available
    Product CodeApplicationsDatasheetMSDSPack SizeList PriceQuantity
    LNK263BCJdatasheet pdfdatasheet pdf datasheet pdf datasheet pdf1 Conjugation For 2mg Antibody
    LNK263B
    LNK261BCJdatasheet pdfdatasheet pdf datasheet pdf datasheet pdf3 Conjugations For 20µg Antibody
    LNK261B
    LNK262BCJdatasheet pdfdatasheet pdf datasheet pdf datasheet pdf3 Conjugations For 200µg Antibody
    LNK262B
    Summary
    Secondary Antibodies
    Negative Isotype Controls
    Useful Reagents
    Positive Controls
    Histology Controls
    More Images
    References
    Reviews
    -
    • LYNX Rapid Plus Biotin (Type 1) Antibody Conjugation Kit® enables the rapid conjugation of a pre-prepared lyophilized mixture containing Biotin label to an antibody or protein in minutes. Activation of proprietary reagents within the antibody-label solution results in the coupling of the antibody to Biotin.

      The LYNX Rapid Plus Conjugation kit® can be used to label small quantities of antibody/protein at near neutral pH, allowing a high conjugation efficiency with 100% antibody recovery and no requirement for desalting or dialysis.

      This kit has been optimized for the additional use of a streptavidin labelled reagent. For customers intending to capture their conjugate on Streptavidin coated plates, we recommend our LYNX Rapid Plus Biotin (Type 2) Antibody Conjugation Kit instead.
    • Intended Use
    • Product Form
    • Reconstitution
    • Preparation
    • Preservative Stabilisers
    • Purity
    • Approx. Protein Concentrations
    • Reagents In The Kit
      Pack Size: 3 Conjugations For 20µg Antibody3 Vials of 10ug LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 3 Conjugations For 200µg Antibody3 Vials of 100ug LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 1 Conjugation For 2mg Antibody1 Vial of 1mg LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 3 Conjugations For 20µg Antibody3 Vials of 10ug LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 3 Conjugations For 200µg Antibody3 Vials of 100ug LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 1 Conjugation For 2mg Antibody1 Vial of 1mg LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 3 Conjugations For 20µg Antibody3 Vials of 10ug LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 3 Conjugations For 200µg Antibody3 Vials of 100ug LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
      Pack Size: 1 Conjugation For 2mg Antibody1 Vial of 1mg LYNX Rapid Plus lyophilized Biotin mix
      1 Vial LYNX Modifier reagent
      1 Vial LYNX Quencher reagent
    • Preparing The Antibody
      Pack Size: 3 Conjugations For 20µg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 10-20 μg antibody be used in each labelling reaction. For optimal results the antibody volume should be 4-10 μl, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 3 Conjugations For 200µg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 100-200 μg antibody be used in each labeling reaction. For optimal results the antibody volume should be 40-100 μl, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 1 Conjugation For 2mg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 2mg antibody be used in each labeling reaction. For optimal results the antibody volume should be 400-1000ul, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 3 Conjugations For 20µg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 10-20 μg antibody be used in each labelling reaction. For optimal results the antibody volume should be 4-10 μl, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 3 Conjugations For 200µg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 100-200 μg antibody be used in each labeling reaction. For optimal results the antibody volume should be 40-100 μl, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 1 Conjugation For 2mg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 2mg antibody be used in each labeling reaction. For optimal results the antibody volume should be 400-1000ul, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 3 Conjugations For 20µg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 10-20 μg antibody be used in each labelling reaction. For optimal results the antibody volume should be 4-10 μl, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 3 Conjugations For 200µg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 100-200 μg antibody be used in each labeling reaction. For optimal results the antibody volume should be 40-100 μl, at a concentration range between 1mg/ml and 2.5 mg/ml.
      Pack Size: 1 Conjugation For 2mg AntibodyThe following buffer solutions are recommended:for preparing the antibody:

      10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.

      Do not use buffers containing nucleophilic components (e.g primary amines), thiols (e.g. Thiomersal/Thimerosal), Merthiolate, Glycine or Proclin. These substances may react with LYNX chemicals. Azide (0.02-0.1%), EDTA and common non-buffering salts and sugars have little or no effect on conjugation efficiency.

      It is recommended that up to 2mg antibody be used in each labeling reaction. For optimal results the antibody volume should be 400-1000ul, at a concentration range between 1mg/ml and 2.5 mg/ml.
    • Test Principle
    • Buffer Solution
    • Storage
      Store kit at -20oC only.
      Newly-conjugated antibody can be stored at 4oC. For long term storage however, the addition of a preservative is recommended.
      Storage in frost-free freezers is not recommended.
      This product should be stored undiluted.
      Avoid repeated freezing and thawing.
      Store kit at -20oC only.
      Newly-conjugated antibody can be stored at 4oC. For long term storage however, the addition of a preservative is recommended.
      Storage in frost-free freezers is not recommended.
      This product should be stored undiluted.
      Avoid repeated freezing and thawing.
      Store kit at -20oC only.
      Newly-conjugated antibody can be stored at 4oC. For long term storage however, the addition of a preservative is recommended.
      Storage in frost-free freezers is not recommended.
      This product should be stored undiluted.
      Avoid repeated freezing and thawing.
    • Shelf Life
      12 months after despatch.
      12 months after despatch.
      12 months after despatch.
    • Acknowledgements
    • Licensed Use
      Bio-Rad LYNX Rapid Plus Conjugation kits® are offered for research purposes alone, and are not intended for human, therapeutic or diagnostic use. The purchase of this conjugation kit conveys to the buyer (whether the buyer is a not-for-profit, academic or for-profit entity) the non-transferable right to use the amount of product purchased and the components of the product for in-house research. The buyer shall not sell or otherwise transfer this product, its components, or materials prepared therefrom to any third party. The buyer shall not use this product or its components for commercial purposes. For the avoidance of doubt, ‘commercial purposes’ means any activity by a party for consideration and includes, without limitation, use of the product or its components (i) in the manufacturing of conjugated materials (e.g. labeled antibodies), (ii) to provide a service, information or data, (iii) for therapeutic, diagnostic or prophylactic purposes, or (iv) for repackaging/resale, whether or not such product or its components are resold for use in research. The use of this product by the buyer constitutes agreement with the terms of this limited use label license for LYNX products.
    • Regulatory
      For research purposes only
    • This product has been reported to work in the following applications. This information is derived from testing within our laboratories, peer-reviewed publications or personal communications from the originators. Please refer to references indicated for further information. For general protocol recommendations, please visit the antibody protocols page.

    • Application NameYesNoMin DilutionMax Dilution
      Conjugation
    • Application NameYesNoMin DilutionMax Dilution
      Conjugation
    • Application NameYesNoMin DilutionMax Dilution
      Conjugation


    • We recommend that for each conjugation the user determines the best antibody:conjugate ratio.
    • Technical Advice
    • Technical Advice
    • Technical Advice
    • Recommended Protocol
    • Recommended Protocol
    • Recommended Protocol
    • ELISA
    • ELISA
    • ELISA
    • Immunohistology
    • Immunohistology
    • Immunohistology
    • Histology Positive Control Tissue
    • Histology Positive Control Tissue
    • Histology Positive Control Tissue
    • Immunofluorescence
    • Immunofluorescence
    • Immunofluorescence
    • Western Blotting
    • Western Blotting
    • Western Blotting
    • Instructions For Use
      1. Before you add antibody to the Lynx Rapid Plus mix, add 1 μl of Rapid Modifier reagent for each 10 μl of antibody to be labelled. Mix gently.

      2. Remove the screw cap from the vial of Lynx Rapid Plus mix and pipette the antibody sample (with the added Rapid Modifier) directly onto the lyophilised material. Resuspend gently by withdrawing and re-dispensing the liquid once or twice using a pipette.

      3. Replace cap on the vial and leave standing for 15 minutes at room temperature (20-25 0C). Longer incubation times could have negative effects on the conjugate.

      4. After 15 minutes incubation, add 1 μl of Lynx Rapid Plus Quencher reagent for every 10 μl of antibody used. The conjugate can be used after 4 minutes. The conjugates do not require purification.
    • Instructions For Use
      1. Before you add antibody to the Lynx Rapid Plus mix, add 1 μl of Rapid Modifier reagent for each 10 μl of antibody to be labelled. Mix gently.

      2. Remove the screw cap from the vial of Lynx Rapid Plus mix and pipette the antibody sample (with the added Rapid Modifier) directly onto the lyophilised material. Resuspend gently by withdrawing and re-dispensing the liquid once or twice using a pipette.

      3. Replace cap on the vial and leave standing for 15 minutes at room temperature (20-25 0C). Longer incubation times could have negative effects on the conjugate.

      4. After 15 minutes incubation, add 1 μl of Lynx Rapid Plus Quencher reagent for every 10 μl of antibody used. The conjugate can be used after 4 minutes. The conjugates do not require purification.
    • Instructions For Use
      1. Before you add antibody to the Lynx Rapid Plus mix, add 1 μl of Rapid Modifier reagent for each 10 μl of antibody to be labelled. Mix gently.

      2. Remove the screw cap from the vial of Lynx Rapid Plus mix and pipette the antibody sample (with the added Rapid Modifier) directly onto the lyophilised material. Resuspend gently by withdrawing and re-dispensing the liquid once or twice using a pipette.

      3. Replace cap on the vial and leave standing for 15 minutes at room temperature (20-25 0C). Longer incubation times could have negative effects on the conjugate.

      4. After 15 minutes incubation, add 1 μl of Lynx Rapid Plus Quencher reagent for every 10 μl of antibody used. The conjugate can be used after 4 minutes. The conjugates do not require purification.

    Additional Biotin (Type 1) Conjugation Kit Formats

    Formats Applications Sizes available
    Biotin (Type 1) Conjugation Kit : Kit CJ 3 Conjugations For 200µg Antibody | 1 Conjugation For 2mg Antibody | 3 Conjugations For 20µg Antibody
    • Copyright © 2016 Bio-Rad

    Recommended Secondary Antibody

      Recommended Negative Isotype Control

        Useful Reagents

          Recommended Positive Controls

            Histology Controls

              Write your review

              You may also be interested in...